OEE Lab / Tools / Units per Hour Calculator

Units per Hour Calculator

Get units per hour from a count and hours, from a cycle time, or from takt. It converts both ways and checks your pace against what demand asks for.

What do you know?

Pick a starting point. Everything else converts from it.

Counted over the hours below.
h
The time those units took.
h
Turns the rate into units per shift.
sec
The pace demand asks for. Leave empty to skip the check.
Units per hour
-UPH
-
your cycle vs takt100% = at limit
Seconds per unit
-
Minutes per unit
-
Units per minute
-
Units per shift
-
UPH takt asks for
-
Margin per hour
-

Want a second look at this result?

Leave your work email if you would like the OEE Lab team to get in touch about your numbers. To keep the result, use Copy link or Print above.

Thanks, we have your email.

No newsletter, no spam.

A good hourly average can hide short stops.

Fabrico, a light MES for OEE, takes stops, speed and counts live from PLCs or IoT sensors, with add-on AI cameras counting output where a machine has no usable signal. Where cameras are fitted, video of any stop can be streamed on request next to its machine data. See it live in Fabrico.

See where your line loses this time: book a demo with a Fabrico consultant.

Request a demo Contact us
Our tools stay free either way.

One pace, three ways to write it

Units per hour (UPH), seconds per unit and takt time are the same pace written in different ways. This tool moves between them, then checks your pace against the one demand asks for.

UPH formulas

UPH = units / hours
UPH = 3,600 / cycle time (sec) × units per cycle
Required UPH = 3,600 / takt time (sec)
Seconds per unit = 3,600 / UPH
3,600 is the number of seconds in an hour, and each formula also runs backward.

Example: 1,800 units in 7.5 hours

Example: a cell makes 1,800 units in a 7.5-hour shift. That is 1,800 / 7.5 = 240 UPH, or 3,600 / 240 = 15 seconds per unit.

Demand sets a takt of 16 seconds, so the pace it asks for is 3,600 / 16 = 225 UPH. The cell beats that by 15 units an hour, and its 15-second pace is 93.75% of takt, so the margin is thin.

Takt time to UPH, at a glance

Divide 3,600 by the takt in seconds. Here are common values.

Takt (sec)UPH requiredUnits in a 7.5 h shift
103602,700
152401,800
201801,350
30120900
4580600
6060450
9040300
12030225
Required pace at each takt, before any allowance for stops.

Takt time vs UPH: what is the difference?

Takt comes from demand, so it tells you the pace you need. UPH can be either that needed pace or the pace you measured, so always say which one you mean.

When a report says 240 UPH, ask how it was worked out. A count over hours is real output, while a rate from cycle time is what the line does with no stops at all.

The rule of thumb is simple. Your measured UPH must be at or above the UPH takt asks for, just as your cycle must be at or below takt.

For the wider comparison, read takt time vs throughput and takt time vs cycle time vs lead time.

Why cycle-time UPH runs high

The rate from a cycle time assumes the line never stops and never makes a reject. Real good output per scheduled hour is that rate times OEE.

From the 15 s cycle (no losses)240 UPH
What a 16 s takt asks for225 UPH
Good units at 75% OEE (240 × 0.75)180 UPH
Example: on paper the cycle beats takt, but at 75% OEE the line is 45 units an hour short.

So check takt against measured good units, or against the cycle after losses. The OEE calculator gives the figure to use.

Slips that throw UPH off

  • Mixing seconds and minutes. A 1.5-minute takt is 90 seconds, which gives 40 UPH.
  • Using hours you did not schedule. Take breaks out of the hours, or your UPH will look low for no reason.
  • Forgetting units per cycle. A 4-cavity mold with a 30-second cycle makes 480 UPH, while the same cycle with one cavity makes 120.
  • Averaging UPH across products. Different products run at different paces, so work out each one, or use the mixed model takt time calculator.
  • Confusing UPH with labor output. Divide by people as well and you get units per labor hour.

Takt and UPH questions

How do you convert takt time to UPH?

Divide 3,600 by the takt time in seconds. A 15-second takt asks for 240 UPH, and a 60-second takt asks for 60. If your takt is in minutes, divide 60 by it instead.

How do you convert UPH to takt or cycle time?

Divide 3,600 by the UPH to get seconds per unit. 240 UPH is 15 seconds per unit. It is a true takt only if the UPH came from demand, so otherwise it is your pace.

How do you calculate UPH from cycle time?

Divide 3,600 by the cycle time in seconds, then multiply by the units made per cycle. A 15-second cycle making one unit gives 240 UPH. That figure leaves out stops and rejects.

Is takt time the same as UPH?

They are not the same thing, though each converts into the other. Takt is a time per unit set by demand, and UPH is a rate that can be either required or measured. See the takt time calculator to get takt from your demand.

How do you calculate units per hour from a shift's output?

Divide the units by the hours they took. 1,800 units over 7.5 hours is 240 UPH. For good units against a plan, use the throughput calculator.

← All OEE Lab tools · Open the takt time calculator →