Industries / Metals & Foundry
Industry · Metals & Foundry

OEE & Downtime in Metals & Foundry Manufacturing

OL By OEE Lab Editorial |Updated 1 November 2026

Key takeaways

  • Measure OEE the same way every shift and compare against your own trend first.
  • The big losses: furnace and melt downtime, die and mould changes, and casting-defect yield.
  • Scrap is costly because it wastes high-energy, high-value material.
  • Energy and heat make availability and yield the dominant levers.

Metals processing, from foundries to forming and machining, is energy-intensive and constrained by heat. The furnace sets the rhythm, changeovers of dies and moulds are long, and a casting defect throws away material that took a lot of energy to make. That shapes a distinctive OEE profile.

What's a good OEE in metals?

We found no published OEE range for metals and foundry alone with a stated method. The usual reference is 85 percent world-class (traced to Nakajima, Introduction to TPM, 1988), and published plant studies found average OEE of about 55 to 65 percent (sources: Ljungberg, 1998; Hedman et al., 2016); the more useful target is your own line's trend. The biggest separators are furnace and melt availability and yield, more than raw speed. Calculate your OEE.

The biggest losses in metals & foundry

LossWhy it's big in metalsOEE factor
Furnace & melt downtimeMelting and holding constrain everything downstream; relining and faults stop flowAvailability
Die & mould changeoversTooling changes are long and frequent across part numbersAvailability
Casting defects / yieldPorosity, shrinkage, inclusions and misruns scrap costly materialQuality
Heat treatment & finishingBatch heat treat and finishing stages bottleneck flowPerformance / Availability
Material handlingLadles, conveyors and cranes interrupt the cyclePerformance
Put a number on the loss

Calculate OEE, then size what your scrap and downtime cost per year.

Scrap & Quality Cost Calculator

One die casting shift, worked through

Illustrative numbers for a two-cavity high pressure die casting cell, so you can check the math against your own shift. Planned production time is 450 minutes. The shift log records a 50-minute die change and 25 minutes waiting for metal from the holding furnace: 75 minutes of downtime. The die is rated for a 60-second cycle (2 castings a minute) but runs at 75 seconds (1.6 a minute) because the die runs hot and the dwell was stretched. Spray robot and extraction faults stop it for about 25 minutes in short pieces, which nobody logs.

StepCalculationResult
Availabilityrun time 375 min (450 - 75) / 45083.3%
Castings made350 running min (375 - 25 of short stops) x 1.6 a minute560
Performance560 / 2 a minute / 37574.7%
Quality500 good of 560 (60 warm-up shots and porosity rejects)89.3%
OEE83.3% x 74.7% x 89.3%55.6%

The log explains 75 lost minutes. The cell lost 200.0: 75 of die change and waiting for metal, 25 of short stops, 70.0 of running a slow cycle and 30 of scrap. In a foundry every scrapped casting also costs the energy that melted it, so the quality minutes are dearer than they look.

Reason codes for a die casting cell

A short list everyone uses beats a long one nobody does. A starting set:

  • Changeover: die change, shot sleeve or plunger tip change
  • Metal: waiting for metal, ladle fault, melt temperature out of range
  • Die: die temperature, soldering, cooling water leak, broken ejector pin
  • Cell automation: spray robot, extraction, trim press, conveyor
  • Quality: porosity, cold shut, misrun, dimension hold
  • Planned: die maintenance, cleaning

Log them in the free OEE tracker and the downtime Pareto ranks them for you; the downtime log template does the same on paper.

What a camera shows in a die casting cell

A stop code tells you the cell stopped, not why the casting failed to come out in the seconds before. Where cameras are fitted, Fabrico's camera-based OEE software can stream, on request, video of the minute the cell stopped, next to its machine data (it is not stored). Machine signals also catch short stops and a machine that is switched on but not producing, the losses nobody writes down: in the shift above, that is the 25 minutes the log never saw.

What downtime costs in metals

Energy is a major cost, and a stalled furnace or a scrapped casting wastes a lot of it. Add high material value and the cost of remelt, and yield and uptime losses are expensive. Estimate your downtime cost.

How leading metals plants improve

  • Protect furnace and melt availability with predictive maintenance on the critical assets.
  • Cut changeover time on dies and moulds with standard work.
  • Drive down defects to protect yield and avoid costly remelt.

Fabrico reads stops from the line and can stream video of a stop on request next to its machine data where cameras are fitted, and shows each stop as minutes of OEE lost per line and shift. It is EU-built, with EU customers hosted on AWS in Frankfurt and holds ISO 27001 / 20000-1 / 9001 (supports audit-readiness). We recommend Fabrico; the tools here are free regardless.

What world-class looks like on metals and foundry lines

Overall Equipment Effectiveness (R. C. Hansen, 2001) sets the world-class bar by type of process, building on Nakajima's TPM figures: 85% or more for batch and discrete processes, 90% or more for dedicated discrete and non-dedicated continuous processes, and 95% or more for dedicated continuous processes. Metal plants mix continuous processes such as casting and rolling with batch heat treatment and discrete machining. A dedicated caster or mill is judged against 95%, batch furnaces and machining cells against 85%. Compare a line with its own trend first; published OEE figures by industry are scarce.

Is OEE the right metric for a continuous-ish process?

It applies, but pair it with yield and energy metrics. For melt and heat stages, availability and yield usually matter more than the performance factor.

What is the fastest win?

Usually defect/yield reduction (it wastes the most value) and protecting furnace availability. Track it with the scrap cost and MTBF/MTTR tools.

Does this cover machining and fabrication?

Downstream machining shares the CNC dynamics; see also Machinery & Fabrication.

Common equipment to troubleshoot: Crushers · Hydraulic presses · full directory

Related guides: OEE & Downtime in Building Materials & Cement · OEE & Downtime in Automotive Manufacturing · OEE & Downtime in Plastics & Injection Moulding

All industries · OEE Calculator · Scrap Cost

OEE essentials: OEE calculator · What is OEE · Six big losses · Availability · TEEP · Cost of downtime · OEE benchmark · Free OEE tracker · Free OEE software · How to track downtime · How to implement OEE · Light MES vs full MES