Blog / Lean
Lean · Guide

Takt Time Board: What to Show and How to Run It

OL By OEE Lab Editorial |Updated 2 November 2026 |5 min read
Short answer

A takt time board shows the crew four things at the line: takt, the plan count so far, the actual count and the gap. Plan so far = working seconds elapsed / takt. Example: at a 72-second takt, the plan after 3 working hours 45 minutes is 187 units, so 176 made means 11 behind, or 13.2 minutes of work.

What the board is for

A takt board answers one question while there is still time to act: are we ahead or behind right now? A report at the end of the shift can only explain what already happened.

It works when anyone on the line can read it in a few seconds. So four numbers beat a screen full of charts.

Takt
72 s
Plan so far
187
Actual
176
Gap
-11
The example board at 11:00. Four numbers, readable from the far end of the line.

How the plan count works

Example: a hypothetical line runs 07:00 to 15:30, with breaks at 09:00 (15 minutes), 11:30 (30 minutes) and 13:30 (15 minutes). That leaves 450 working minutes, or 27,000 seconds.

Demand is 375 units, so takt = 27,000 / 375 = 72 seconds, which is 50 units a working hour. You can check this with the takt time calculator.

Plan so far = working seconds elapsed / takt
225 min x 60 = 13,500 s
13,500 / 72 = 187.5, shown as 187
At 11:00 the line has worked 240 minutes minus the 15-minute break. Round the plan down to whole units.

The clock must stop during breaks, or the plan keeps climbing while nobody works. So program the break times in, or the board will tell the crew they are behind when they are not.

One morning on the board

HourPlanActualPlan so farActual so farGap
07-0850465046-4
08-09504910095-5
09-10 (break)37.536137131-6
10-115045187176-11
The gap grew by 5 between 10:00 and 11:00. That is the hour to ask about.

A gap of 11 units at 72 seconds each is 792 seconds, or 13.2 minutes of work. Saying "13 minutes behind" often lands better on the floor than a unit count.

Shift plan375
Plan so far187
Actual so far176
Share of the 375-unit shift plan at 11:00. A gap of 3 points looks small, and it is already 13 minutes of work.

What is a takt clock?

A takt clock counts down one takt, then resets. On a paced line, each station should finish as it reaches zero.

It helps on a line with long takts, such as several minutes, where nobody can feel the pace. On a 20-second line it just flickers, so a running count serves the crew better.

  • Count-up board: shows plan and actual. It suits most lines and needs one count at the end.
  • Countdown clock: shows time left in this takt. It suits long-cycle assembly.
  • Both: a clock for the pace and a count for the score. It suits a line where one late station holds up the rest.

Three ways to build one

TypeWhat it needsFits when
WhiteboardMarker, hourly plan printed in advance, one person who writes it upYou are starting out, and hourly updates are enough
Counter with displayA part counting sensor and a large LED displayYou want a live count at one line
Screen fed from line dataA screen at the line, plus a source of counts such as PLC signalsYou want it on many lines, with history kept
Start with the simplest one the line will really keep up to date.

A whiteboard is the same idea as an hour-by-hour production board, and that guide covers how to run it day to day. This page adds what changes when takt itself is on display.

Rules that keep it honest

  1. Count good units at the end of the line. A count taken earlier hides the rejects.
  2. Set takt from demand. If it was set from what the line can do, the board can never show a real gap.
  3. Change takt when the plan changes. If demand moves to 400 units, takt is 67.5 seconds, or 53.3 units an hour, and the board has to show it.
  4. Fix a rule for changeovers. Decide whether the plan pauses, and keep to it, since how to count changeovers in OEE faces the same choice.
  5. Treat being ahead as a signal too. A line far ahead of takt is building stock nobody asked for yet.

What to do when the gap grows

Agree the trigger in advance, so that nobody needs to decide under pressure. Example rule: at a gap of 5 units, the team leader goes to the line, and at 10 units, the supervisor does.

Write the reason next to the hour, even in two words. The notes feed the daily production meeting, and an andon call can bring help sooner.

How good boards go stale

  • Showing OEE in place of takt. OEE is a fine shift figure, and the crew still needs a count they can act on right now.
  • Mounting it where only managers walk. Test it from the farthest station on the line.
  • Too small a font or too many numbers. If you need to walk up to read it, it will not get read.
  • One takt on a mixed line. When models take different work, an average takt can mislead, so use the mixed-model takt time calculator and plan by sequence.
  • Using the board to blame. If a gap brings only trouble, the count starts to bend.
See it live in Fabrico

A board is only as good as its count. Fabrico takes counts, speed and stops live from PLCs or from external sensors on older machines, so the count at the line is not written up by hand. See how Fabrico connects machines.

What people ask next

What should a takt time board show?

Takt, the plan count so far, the actual count and the gap. Add a line for the reason when the gap grows. Keep it readable from the far end of the line.

How do you calculate the plan count on a takt board?

Divide the working seconds elapsed by takt, and leave breaks out of the elapsed time. At 13,500 seconds and a 72-second takt, the plan is 187 units. Get takt from the takt time calculator.

What is a takt time clock?

It is a countdown that runs for one takt and then resets. Each station aims to finish as it reaches zero. It helps most on long-cycle lines, where the pace is hard to feel.

Is a takt board the same as an hour-by-hour board?

They overlap a lot. An hour-by-hour production board tracks plan and actual each hour, while a takt board puts takt on display and often updates per unit.

Can I build a takt board in Excel?

Yes, for a start. Enter takt and break times, calculate the plan from the clock, and type or import the actual count on a screen at the line. A part counting sensor can replace the typing later.

See OEE per line and shift on your own machines

Fabrico is a light MES for OEE. It takes stops, speed and counts from PLCs or IoT sensors, with add-on AI cameras counting output where a machine has no usable signal, and operators tag the cause at the line.

Book a Fabrico demo

← More OEE Lab guides · The hour-by-hour production board →

OEE essentials: OEE calculator · What is OEE · Six big losses · Availability · TEEP · Cost of downtime · OEE benchmark · Free OEE tracker · Free OEE software · How to track downtime · How to implement OEE · Light MES vs full MES