Troubleshooting / Bagging machine

Bagging Machine Troubleshooting

The most common bagging machine problems on the plant floor, with the likely causes and the fix for each. Part of the OEE Lab troubleshooting directory.

Not your exact symptom?

Describe it in the symptom finder and search the whole directory.

Open the symptom finder

Problems on this page:

Bag weight out of spec

Hits OEE: Quality

Symptoms: Over/under-weight bags, giveaway, checkweigher rejects.

Weigher/feeder calibration
Recalibrate the scale/feeder; check the dribble feed.
Product density or flow change
Adjust for density; manage product condition.
Timing between fill and clamp
Tune fill cut-off and bag-clamp timing.

Prevention: Scale calibration, product control, timing checks.

Poor seal or closure

Hits OEE: Quality

Symptoms: Open or weak seams, leaking bags, stitching/heat-seal faults.

Heat-seal temperature/pressure wrong
Tune seal heat, pressure and dwell for the bag.
Contamination in the seal area
Improve dust control; clean the seal zone.
Stitching/closure mechanism fault
Service the sewing head or seal bars.

Prevention: Validated seal settings, clean seal area, closure maintenance.

Bag placement or no-bag fault

Hits OEE: Availability

Symptoms: No bag presented, mis-placed bags, spills, stops.

Bag magazine or pick fault
Refill; service the vacuum pick and magazine.
Bag quality or static
Tighten bag spec; manage static/curl.
Sensor or timing issue
Check bag-present sensors and timing.

Prevention: Magazine/pick maintenance, bag quality, sensor checks.

Dust escaping at the filling spout

Hits OEE: Quality

Symptoms: Dust around the spout, product on the floor, dirty bags.

Spout seal worn
Replace the spout seal.
Bag clamp not sealing
Adjust or repair the clamp.
Dust extraction weak
Check the extraction.
Fill rate too high at the end of the fill
Slow the final fill.

Prevention: Spout seals checked weekly.

Bags splitting or bursting

Hits OEE: Quality

Symptoms: Bags split at filling, on the conveyor or on the pallet.

Bag strength not suited to the product
Check the bag specification.
Overfilling
Check the fill weight.
High drop at discharge
Lower the drop height.
Sharp edges on conveyors
Remove sharp edges.

Prevention: Bag supplier checks at goods in.

Product bridging in the hopper

Hits OEE: Availability

Symptoms: Product stops flowing from the hopper and fills slow down or stop.

Damp product
Check product moisture.
Hopper walls too shallow for the product
Fit flow aids or a liner.
Agitator or flow aid failed
Repair the agitator or vibrator.

Prevention: Flow aids checked at start-up.

Bag discharge faults

Hits OEE: Availability

Symptoms: Filled bags do not release, fall over or jam at the transfer.

Bag clamp not releasing
Check the clamp and its valve.
Kicker or flattener fault
Check the mechanism and its sensor.
Conveyor speed mismatch
Match conveyor speeds.

Prevention: Transfers checked after any changeover.

Poor bag shape for palletising

Hits OEE: Quality

Symptoms: Bulging or uneven bags make unstable pallets.

Bag flattener or settler not working
Check the flattener and settler.
Air trapped in the product
Use de-aeration or vent the bags.
Bag size wrong for the fill
Use the right bag size.

Prevention: Pallet stability checked per shift.

Checkweigher rejects bags the bagger passed

Hits OEE: Quality

Symptoms: The checkweigher rejects bags that the bagging scale reported as in spec.

Bagging scale not calibrated
Calibrate the scale with test weights.
Product hanging up in the spout
Check that the spout empties before the bag is released.
Checkweigher zero drift
Zero and calibrate the checkweigher.
Vibration from nearby machines reaching the scale
Isolate the scale frame from vibration.

Prevention: Both scales checked with the same test weights on a schedule.

Guidance only. Always follow lockout/tagout and your site's safe-work procedures, and verify against OEM manuals before acting.

Related equipment guides: shrink wrapper · stretch wrapper · packaging line · case packer

Stop the same fault coming back

Recurring bagging machine stops usually trace to a cause you cannot see by hand. We recommend Fabrico: it tracks OEE and downtime live from PLCs or IoT sensors, with add-on AI cameras counting output where a machine has no usable signal; where cameras are fitted, the video of any stop can be streamed on request next to its machine data so the cause can be reviewed; and every stop shows up as minutes of OEE lost per line and shift. EU customers are hosted on AWS in Frankfurt, and Fabrico and the company behind it hold ISO/IEC 27001, ISO/IEC 20000-1 and ISO 9001.

Book a Fabrico demo
The directory stays free.

Related tools: full troubleshooting directory · OEE calculator · downtime cost · MTBF / MTTR · glossary

Methods that cut recurring stops: the six big losses · root cause analysis · preventive vs predictive maintenance · SMED & changeover

OEE essentials: OEE calculator · What is OEE · Six big losses · Availability · TEEP · Cost of downtime · OEE benchmark · Free OEE tracker · Free OEE software · How to track downtime · How to implement OEE · Light MES vs full MES