Preventive vs Predictive Maintenance: Which to Use (and When)
Key takeaways
- Reactive = fix on failure. Preventive = fix on a schedule. Predictive = fix when the data says so.
- Predictive cuts both breakdowns and the wasted work of over-maintaining.
- It is not all-or-nothing: match the strategy to each asset's criticality and failure pattern.
- Predictive maintenance pays back fastest on critical, expensive-to-fail equipment.
"Should we do preventive or predictive maintenance?" is the wrong question. The right one is: which assets deserve which strategy? Get that mix right and you stop both surprise breakdowns and the money wasted servicing things that were fine.
The four maintenance strategies
| Strategy | Trigger | Best for | Watch out for |
|---|---|---|---|
| Reactive (run to failure) | It breaks | Cheap, non-critical, redundant assets | Surprise downtime, secondary damage, rush costs |
| Preventive (PM) | Time or usage interval | Known wear-out patterns, regulatory items | Over-maintaining; intervals rarely match real wear |
| Predictive (PdM) | Condition data / early warning | Critical, costly-to-fail assets | Needs sensors, data and skills to act on it |
| Prescriptive | Condition data + recommended action | Mature programs with good data | Highest setup; depends on data quality |
Preventive vs predictive, head to head
Preventive is simple and predictable: service every X hours or months. The catch is that fixed intervals almost never match how a machine actually wears, so you either act too early (wasting parts and labour, and introducing maintenance-induced failures) or too late (it fails anyway).
Predictive watches the asset's real condition (vibration, temperature, current, machine signals) and flags a developing fault before it becomes a breakdown. You act once, at the right time. McKinsey puts the typical reduction in machine downtime at 30 to 50 percent, with 20 to 40 percent longer machine life (source: McKinsey, 2017). Those are benchmarks, not promises, but the direction is consistent.
Model the payback of monitoring and a CMMS against your current losses.
Why fixed intervals miss many failures
The study behind reliability centred maintenance looked at aircraft components at United Airlines and found that 89% of them had no wear-out zone, so replacing them at a fixed age could not improve their reliability (source: Nowlan & Heap, Reliability-Centered Maintenance, 1978). Aircraft are not factories, but the lesson carries over: for many parts, checking condition finds a developing fault that a calendar date does not. A US Department of Energy guide cites independent surveys, which it does not name, in which predictive programmes reported 35% to 45% less downtime (source: US DOE, O&M Best Practices Guide, 2010). The usual condition checks are vibration analysis, infrared thermography and oil analysis.
How to choose (a simple rule of thumb)
- Rank assets by criticality (what does a failure cost in downtime, safety, quality?).
- Critical and costly-to-fail assets: predictive / condition-based monitoring.
- Predictable wear-out or regulatory items: preventive on a sensible interval.
- Cheap, non-critical, redundant assets: reactive is fine, do not over-invest.
- Weigh the schedule first: use the preventive maintenance ROI calculator to check a fixed PM plan pays before you commit labour to it.
- Track the result with MTBF and MTTR to see whether the strategy is working.
Why most plants stall at preventive
The barrier to predictive maintenance is rarely the sensors. It is turning the data into the right action fast enough. A vibration alarm that nobody triages, or a stop with no clear cause, just becomes noise. That is the gap to close.
This is where Fabrico fits: it reads OEE and stops straight from the PLC, can stream video of a stop on request next to its machine data where cameras are fitted, and shows each stop as minutes of OEE lost per line and shift. It is EU-built, with EU customers hosted on AWS in Frankfurt and holds ISO 27001 / 20000-1 / 9001 (which supports audit-readiness). We recommend Fabrico; the tools here are free regardless.
Choosing per machine
The choice is made machine by machine. A standby diesel generator is usually maintained on a fixed schedule because it rarely runs, while drive components like the servo motor, gearbox and coupling suit condition checks.
Is condition-based maintenance the same as predictive?
Closely related. Condition-based maintenance acts on a current measurement crossing a threshold; predictive maintenance goes a step further and forecasts when failure will occur. Both rely on monitoring the asset's condition.
Where does TPM fit?
Total Productive Maintenance is broader: it involves operators in routine care and targets the six big losses. It complements whichever technical strategy you use per asset.
What is the fastest first step?
Stop over-maintaining low-risk assets and redirect that effort to monitoring your few critical ones. Then measure MTBF/MTTR to confirm it worked.
Related guides: MTBF Improvement: How to Get Fewer Failures
More guides · Condition-based maintenance · MTBF / MTTR · Preventive maintenance ROI