A shop floor kiosk is a fixed screen or device at the line where operators report stops, causes, counts or job starts. For most lines, choose a wall or machine-mounted rugged tablet or panel PC with a glove-friendly touch screen, wired network where possible, and a locked-down single app. Put one within a few steps of where the operator stands, because distance is what kills data entry.
Start from the task, not the device
Write down what an operator will do at the kiosk, how often and with what on their hands. Those three facts decide most of the hardware.
A cause tag that takes a few seconds, 30 times a shift, needs something very close and very fast. Reading a work instruction once an hour can live on a larger shared screen.
The real hardware options
There are five realistic choices. Many plants use a mix, because one line's needs rarely match another's.
| Type | Best for | Watch out for |
|---|---|---|
| Rugged tablet on a mount | Cause tags, checklists, moving between mounts | Battery ageing in warm areas, small screen from a distance |
| Panel PC, fixed | One station used all day, larger screen, wired network | Fixed position, so the location must be right first time |
| Consumer tablet in a rugged case | Clean areas, pilots | Models change often, weak glove support, dust and heat limits |
| Handheld computer with scanner | Roaming staff, scanning orders and material | Small screen, charging routine, devices get lost |
| Physical button box | A few fixed causes, gloves, dirty work | Few choices, needs wiring to an input module |
Where you put it matters more than which one you buy
The kiosk competes with the machine for the operator's attention. A long walk means entries get saved up and typed at the end of the shift, from memory.
Example: a shared kiosk is 40 metres from the operator, and the line stops 15 times a shift. Assume a walking speed of about 1.2 metres a second.
Nobody will spend 17 minutes a shift walking while the line waits. In practice they stop going, and the log gets filled in at 13:55.
Stand with the operator for an hour before you mark a location. Check that the mount does not block a guard, an e-stop, a walkway or a forklift route, and agree the place with your safety lead.
Screen and touch
- Touch type: capacitive screens are responsive but need a glove-mode setting or thin gloves, while resistive screens respond to pressure from any glove but feel less sharp. Test with the crew's real gloves.
- Size: 8-10 inches suits a few large buttons at arm's length, and 15 inches or more suits lists and readable numbers from further away.
- Brightness: check it where the kiosk will hang, since glare from roof lights or a door can wash out a good screen.
- Buttons: make them large and few, because a stopped line and a gloved hand are poor conditions for small targets.
Dust, water, heat and shock
Most IP ratings come from IEC 60529, where the first digit covers solids and the second covers water (summary of the levels). Read the rating for the whole unit as mounted, including its ports and cables.
- IP54: protected against harmful dust and against splashing water. It can suit a clean and dry assembly area.
- IP65: dust-tight and protected against water jets, a common choice for machining and general production.
- IP69K: high-pressure, high-temperature washdown, the level to ask about for food lines that are hosed down. This one comes from the road-vehicle standard ISO 20653 and DIN 40050-9, with a test at about 80 degrees C and 80-100 bar.
- IP69: IEC 60529 added a similar level 9 in its 2013 amendment, so ask which test the unit passed. Check that materials also suit your cleaning chemicals.
Check the stated operating temperature against the hottest spot on the line, not the hall average. Ask for shock and vibration data if the mount is on a press or a machine frame, or mount it on a separate post.
In a hazardous area, use only equipment certified for that zone, such as ATEX in the EU or IECEx. For electronics assembly, check that the kiosk fits your ESD rules.
Mount, power and network
- Mount: many screens use standard VESA holes, so check the pattern and the weight limit. Lock the device to the mount if tablets tend to wander.
- Power: a fixed supply beats a charging routine that someone will forget. Power over Ethernet can run both power and data on one cable, but the device's draw must fit what the switch port delivers.
- Network: use a wired link where you can. If you must use Wi-Fi, test signal strength at the mounting spot with machines running, because metal frames and motors can spoil a survey done on a quiet day.
- Offline: ask what happens when the network drops. Entries should queue and sync, with the original time stamp.
Scanners, badges and other add-ons
A scanner saves typing wherever orders, material or machines have a code. Many USB scanners act like a keyboard, so they work with most software without extra drivers, and 2D models also read QR codes.
A badge reader saves shared logins and gives you a real name on each entry. Ask whether names are needed at all, because people often report more honestly when the question is what happened and not who did it.
Lock it down
A kiosk should do one job, so it should open your app and nothing else. Each common system has a way to do this, but the setup differs, so check it before you pick the device.
- Windows: Assigned Access signs in a local account that opens one app. Check that your Windows edition supports it.
- Android: lock task mode needs a device policy controller, usually part of a device management tool. Plain screen pinning can be exited by the user.
- ChromeOS: kiosk mode runs on managed devices, set up through the Google Admin console.
- iPadOS: Guided Access is built in and limits the device to one app, set by hand on each one. For fixed kiosks, ask IT about single app mode on supervised devices.
Then, on any system:
- Disable browsers, app stores and personal accounts.
- Turn off sleep during shifts, or set a short wake-on-touch.
- Use a device manager to push updates outside production hours.
- Keep one spare, ready to swap, so that a broken screen does not end data capture for a week.
- Agree with IT how the devices join the network, and keep them apart from the machine controls.
Run a two-week trial first
Put one kiosk on one line before you order 30. Measure three things.
- Entry time: how many seconds from walking up to finished, with gloves on.
- Coverage: what share of stops got a cause within the shift.
- Survival: what is dirty, loose, broken or being ignored after two weeks.
Compare the entries with a machine count if you have one, using the checks in downtime data accuracy. Then ask the crew what they would move or change.
Where kiosk projects go wrong
- Buying before designing the screen. Too many taps will defeat any hardware. Keep the reason list short, as in downtime reason codes.
- One kiosk for a long line. Count the steps from each operator's position.
- No owner. Name who cleans, charges and replaces each device.
- Asking people to time stops. Let sensors or the PLC take the times, and use the kiosk for causes.
Paper can still be the right answer on a line with few stops, as the comparison in shop floor data collection shows. A kiosk earns its place when entries are frequent and need to be seen quickly.
A kiosk works best when it only asks for what a machine cannot know. In Fabrico, stops and counts come from PLCs or IoT sensors and operators tag the cause at the line. See how Fabrico tags stops at the line.
What people ask next
What is a shop floor kiosk used for?
Operators use it to tag stop causes, report scrap, start and finish jobs, complete checks and read instructions. It is a fixed point at the line, so the data gets entered close to the event. See operator downtime logging for what makes this work.
Tablet or panel PC for a shop floor kiosk?
Choose a tablet on a mount if you need flexibility or plan to move it. Choose a panel PC for one busy station that needs a larger screen and fixed power and network. Test both in the real spot if you are unsure.
What IP rating does a shop floor tablet need?
IP65 is a common choice in general production, because it means dust-tight and protected against water jets. Clean and dry assembly can accept less, and hosed-down food lines should ask about IP69K. Check the rating with cables and ports in place.
Can operators use their phones instead of a kiosk?
It can work for roaming staff, but many plants limit personal phones on the floor, and a phone is hard to use with gloves. A shared device also keeps data and logins under company control. Check your site rules first.
How many kiosks does a production line need?
Count the stations where people must report, then check the walking distance from each. One may do for a short cell with one operator. Long lines often need one per zone, placed within a few steps of where the operator stands.
Fabrico is a light MES for OEE. It takes stops, speed and counts from PLCs or IoT sensors, with add-on AI cameras counting output where a machine has no usable signal, and operators tag the cause at the line.