Blog / MES
MES · Guide

Retrofit Sensors for OEE on Older Machines

OL By OEE Lab Editorial |Updated 1 November 2026 |6 min read
Short answer

You can get OEE data from an old machine without opening its controller. A clamp-on current sensor gives run state, and a proximity or photo sensor counts parts. Add a reject count and you have availability, performance and quality. Join the signals, because a motor can run with no output.

When you need a retrofit

Many machines can give you OEE data on day one. Some cannot. A retrofit is the answer when:

  • The machine is old and has no controller output you can read.
  • The controller is closed or the vendor will not open it.
  • You do not want anyone to touch the control logic, for good reason.
  • You want a quick pilot before you spend on integration.

The idea is simple. Instead of asking the machine for its state, you watch it from outside.

Two sensors are enough to start: one for run state, one for parts.

Which sensor for which signal

SignalSensorHow it worksWatch out for
Run stateClamp-on current sensor on the main motor cableCurrent above an idle level means the machine is workingA machine can draw current while making nothing
Run stateLight sensor on a stack lightGreen, amber or red maps to a stateLights show the operator's view, not always the truth
Part countInductive proximity sensorPulses when a metal part or cam passesNeeds metal and a stable gap
Part countPhotoelectric sensorBeam is cut by a package or bottleDust, glare and gaps in the product stream
Reject countSecond sensor at the reject chuteCounts what leaves the line as wasteCount each part once
Speed or cyclePulses per minute from the count sensorGives cycle time without extra hardwareAverages hide slow cycles
Run state on a quiet machineVibration sensorMotion above a level means the machine is onNeeds a test on each machine type

The current sensor and the part sensor are the core pair. They are quick to fit and can be clamped or mounted without cutting a wire.

Opening an electrical cabinet to place a clamp is still a job for a qualified electrician. For the signals a PLC can give you instead, see PLC signals for OEE.

Example: an old press line with two sensors

Example: a press has no network port. A current sensor sits on the main motor cable, and a proximity sensor counts strokes.

Idle current is 2 A, working current is 11 A. The team sets the "running" threshold at 5 A, held for 10 seconds, so a brief spike does not count.

A reject sensor at the chute counts bad parts. The ideal rate is 60 strokes a minute (a 1.0 second cycle). Here is one 480-minute shift:

Measured by sensorsValue
Scheduled time480 min
Run time (current above 5 A and strokes counted)372 min
Strokes counted20,800
Rejects counted416
Good parts20,384
Availability = 372 / 480 = 77.5%
Performance = 20,800 / (372 x 60) = 93.2%
Quality = 20,384 / 20,800 = 98.0%
OEE = 77.5% x 93.2% x 98.0% = 70.8%
Check: (20,384 / 60) / 480 = 70.8%
Two sensors plus a reject count are enough for a full OEE number, with no change to the press.
Planned time480 min
Stopped (current sensor)108 min
Slow running (stroke count)25.3 min
Rejects (chute sensor)6.9 min
Good product at full speed339.7 min
The same shift in minutes: 480 planned, 339.7 good at full speed, so OEE is 70.8%. Hypothetical example.

The method follows Overall Equipment Effectiveness (R. C. Hansen, 2001). For the steps in more detail, see how to calculate OEE.

The trap: current is not output

A motor that spins with no product still draws current. If you use current alone, a press that runs empty for 20 minutes counts as running.

That hides a real loss.

The fix is a rule that joins both signals. Treat the machine as running only when current is high and a part has been counted in the last N seconds.

If current is high and nothing is counted, log it as a stop with the cause to be added, for example "starved".

How to fit sensors safely

1
Pick the signals first
Decide what you must know: run, count, reject. Do not buy sensors before you know this.
2
Choose non-invasive mounts
Clamp-on current sensors and bracket-mounted proximity or photo sensors do not alter the machine.
3
Keep away from safety circuits
Never tap an emergency stop or guard interlock. Let a qualified electrician do any wiring.
4
Set thresholds with the machine running
Record idle and working values, then set the threshold between them with a margin.
5
Check against reality
Watch one hour. Compare the sensor count with a hand count. Fix gaps before trusting the data.
Five steps to fit and prove a retrofit sensor set.

Getting the signal out

The sensors need a small gateway that reads them and sends the data on. Check three things before you buy one:

  • It keeps data when the network drops. A gap in the log looks like a long stop.
  • The clock is right. Every record needs a correct time stamp, or shifts will not match.
  • It reads often enough. To catch a stop of a few seconds, the gateway must see each change, not a minute average.

Wired links are the safe default on a noisy floor with motors and drives. Wireless can work, but test it where the machine sits, close to steel and cabinets.

Common mistakes

  • Counting at the wrong place. Count good output at the end of the machine, not at the infeed.
  • Double counts. A part that passes the sensor twice, or a sensor that bounces, doubles the count. Test with a known batch.
  • A threshold that is too low. A cooling fan can fool a current clamp. Test on the real machine.
  • No cause for stops. A sensor sees that the machine stopped, not why. Add an operator choice. See how to track downtime.
  • Ignoring dirt. Photoelectric sensors need cleaning. Put it in the daily check.

For a wider view of data options, see OEE data collection methods. If the cause matters more than the count, look at computer vision for OEE. For problem sensors, see proximity sensor troubleshooting and photo-eye troubleshooting.

See it live in Fabrico

Fabrico reads stops, speed and counts live from PLCs or from IoT sensors, which are external sensors on older machines, so a machine with no output can still join your OEE view. See how Fabrico connects older machines.

What people ask next

How many sensors do I need per machine?

Two to start: one for run state and one for the part count. Add a third for rejects if you want quality from the sensors. Anything else can come later.

Do I have to stop the machine to fit them?

Clamp-on current sensors and bracket-mounted proximity or photo sensors usually need little or no stop time. Wiring a power supply may need a short stop and a qualified electrician.

Can a sensor tell me why the machine stopped?

No. It tells you that it stopped and for how long. The cause comes from an operator choice or a camera. See downtime reason codes.

What if the machine runs at different speeds?

The count sensor still counts parts, so speed follows from counts per minute. Set the ideal rate per product. See ideal cycle time.

Is a retrofit as good as a PLC signal?

For run state and counts it can be, once you have tested it against a hand count. A PLC can give more, such as fault codes and mode. See PLC signals for OEE.

Related guides: Stack Light Monitoring: Downtime From Tower Lights · Sensor Fault Stops: Find and Fix False Trips · IIoT Gateway: What It Does and When You Need One · MES PLC Integration: Routes, Tag List and Tests

← More OEE Lab guides

OEE essentials: OEE calculator · What is OEE · Six big losses · Availability · TEEP · Cost of downtime · OEE benchmark · Free OEE tracker · Free OEE software · How to track downtime · How to implement OEE · Light MES vs full MES