Blog / Metrics
Metrics · Guide

Garment Line Efficiency: Formula and Example

OL By OEE Lab Editorial |Updated 2 November 2026 |6 min read
Short answer

Garment line efficiency = pieces produced x SAM / (operators x minutes worked) x 100. SAM is the standard allowed minutes for one garment. Example: 420 pieces of a 22-minute polo from 32 operators in 480 minutes gives 9,240 / 15,360 = 60.2%.

The sewing floor's version of line efficiency

A sewing line runs on people, so its efficiency measures labor minutes. It asks how many standard minutes of garments came out, against how many minutes the operators spent on the line.

This is the labor form of line efficiency. It is a different formula from the station-based one engineers use for balance, and how to calculate line efficiency sets the two side by side.

Efficiency = pieces x SAM / (operators x minutes) x 100
Minutes produced = 420 x 22 = 9,240
Minutes available = 32 x 480 = 15,360
Efficiency = 9,240 / 15,360 = 60.2%
Example shift: a line of 32 operators sewing a polo shirt with a SAM of 22 minutes.

What SAM means, and where it comes from

SAM stands for standard allowed minutes, and some plants call it SMV, standard minute value. It is the sum of the standard times for every operation in the garment, including allowances.

The figure comes from a time study or a predetermined time system such as GSD. If the style changes, the SAM changes, so one style's efficiency only compares with another's when both SAMs were set the same way.

How to set the line target

Turn the formula around and you get the target that sewing supervisors post on the line. Target per hour = operators x 60 / SAM x planned efficiency.

Example: 32 x 60 / 22 = 87.3 pieces an hour at 100%. At a planned 70%, the target is 61.1 pieces an hour, or about 489 for the 8-hour shift, so the 420 made fell 69 short.

The 70% here is a planning input for this example, not a benchmark. We found no neutral published garment figure we could check, so set yours from your own past styles.

Track it hour by hour

A single shift figure hides when the line lost its minutes. Each hour has 32 x 60 = 1,920 minutes available, so hourly efficiency is pieces x 22 / 1,920.

Hour 1, 46 pieces52.7%
Hour 2, 54 pieces61.9%
Hour 3, 58 pieces66.5%
Hour 4, 55 pieces63.0%
Hour 5, 38 pieces43.5%
Hour 6, 56 pieces64.2%
Hour 7, 58 pieces66.5%
Hour 8, 55 pieces63.0%
The same 420 pieces split by hour (46, 54, 58, 55, 38, 56, 58, 55). Hour 5 stands out, and hour 1 shows a slow start.

In this example, hour 5 lost time waiting for cut parts. An hour-by-hour production board lets the supervisor see that during the shift, while something can still be done.

Overall vs on-standard efficiency

Many factories keep two versions. Overall efficiency counts every minute on the line, and on-standard efficiency takes out minutes the operators could not sew through no fault of their own.

Example: in hour 5 the whole line waits 20 minutes for cut parts, which is 32 x 20 = 640 operator minutes. On-standard efficiency is 9,240 / (15,360 - 640) = 9,240 / 14,720 = 62.8%.

The gap of 2.6 points belongs to planning and material, and the sewing floor could not have closed it.

Keep both figures, because a report that shows only on-standard can hide a large off-standard problem. For the wait itself, see waiting for material downtime.

Who counts as an operator?

This choice moves the number more than most people expect. The rule is simple: the people in the bottom line must match the work inside the SAM.

Who is countedMinutes availableEfficiency
28 machine operators + 4 helpers32 x 480 = 15,36060.2%
28 machine operators only28 x 480 = 13,44068.8%
Same 9,240 minutes produced, two results. If the SAM includes helper work, count the helpers.

Comparing two lines is only fair when both follow one rule. Write it on the report, and apply it to absences and floaters too.

Do not confuse it with line balance

Sewing engineers also calculate a balance figure, and that one belongs to the other family. It uses operation times from a capacity study and ignores the piece count.

Example: the average work per person, or pitch time, is 22 / 32 = 0.69 minutes. If the slowest operation takes 0.85 minutes, line balance = 22 / (32 x 0.85) = 80.9%, and that operation caps the line at 60 / 0.85 = 70.6 pieces an hour.

So the line could not reach 87.3 pieces an hour even with no stops at all. Against that cap, the shift ran at 420 / (70.6 x 8) = 74.4%, and 80.9% x 74.4% = 60.2%, the same efficiency as before.

That split shows how much of a weak figure comes from balance. The line efficiency calculator makes it for you, and the line balancing calculator helps fix that part.

The daily routine on the line

1
Fix the SAM for the style
Use one approved figure, and record the date it was set.
2
Count passed pieces at end of line
Pieces that pass final check count. Pieces in rework wait until they pass.
3
Log people and minutes
Record operators present each hour, with late starts and early leavers.
4
Record off-standard time
Note machine stops, no cut parts and style changes, with minutes and people affected.
The daily routine for one sewing line.

What bends the number on a sewing floor

  • Counting pieces at the bundle stage. Count what passes at the end of the line, as the good count rule says.
  • Using the buyer's costed SAM. A SAM set for pricing may differ from the method on your floor.
  • Ignoring learning on a new style. The first days of a style run below normal, so do not compare them with a settled style.
  • Treating absences as efficiency. Fewer people on the line changes the bottom of the formula, so log headcount by the hour.
  • Using a piece count per person. Units per labor hour is useful, but it cannot compare a polo with a jacket, and SAM can.

Line efficiency and OEE on a sewing floor

Line efficiency measures people, and OEE measures a production asset against its ideal rate. A sewing line can use both, and OEE for garment manufacturing explains how to set that ideal.

Next, run your own figures through the line efficiency calculator. It is quicker than rebuilding the sum each time a style changes.

See it live in Fabrico

Off-standard minutes are only useful when the cause is written down when it happens. With Fabrico, operators tag the cause of a stop at the line, and stops are shown per line and shift. See how Fabrico tracks stops.

What people ask next

How do you calculate sewing line efficiency?

Multiply the pieces produced by the SAM, then divide by operators x minutes worked. For 420 pieces at 22 SAM, 32 operators and 480 minutes, the result is 60.2%. The line efficiency calculator does the sum.

What is SAM in garment production?

SAM means standard allowed minutes, the time a trained operator should need for one garment, including allowances. It comes from a time study or a predetermined time system. Some plants call the same figure SMV.

How do I calculate the hourly target for a sewing line?

Use operators x 60 / SAM x planned efficiency. With 32 operators, a 22-minute SAM and a planned 70%, the target is 61.1 pieces an hour. Post it on an hour-by-hour production board.

What is the difference between line efficiency and line balance in garments?

Line efficiency uses the piece count and compares output with labor minutes. Line balance uses operation times and shows how evenly work is spread. See how to calculate line efficiency.

What is a good efficiency for a sewing line?

We found no neutral published benchmark we could verify, and style mix changes the result a lot. Track each line against its own results on one fixed SAM and headcount rule. Then look at what costs the most minutes, starting with a downtime Pareto chart.

See OEE per line and shift on your own machines

Fabrico is a light MES for OEE. It takes stops, speed and counts from PLCs or IoT sensors, with add-on AI cameras counting output where a machine has no usable signal, and operators tag the cause at the line.

Book a Fabrico demo

← More OEE Lab guides · Open the line efficiency calculator →

OEE essentials: OEE calculator · What is OEE · Six big losses · Availability · TEEP · Cost of downtime · OEE benchmark · Free OEE tracker · Free OEE software · How to track downtime · How to implement OEE · Light MES vs full MES